我正在运行的Andr​​oid SDK 2.2，并想获得亚行连接到谷歌Nexus One手机。它是一种新的手机，直接从谷歌运 - 没有安装任何应用程序呢。 （我有Windows XP） 以下是我迄今所做的：

随后在设置设备的发展给予对Android开发者网站上的说明： http://developer.android.com/guide/developing/device.html

补充的android：可调试=真正的我的应用程序清单

USB调试的检查在手机上

下载的设备驱动程序对于Windows版本3（该支持的Nexus One手机）

通过硬件安装向导又到安装设备 - 该设备显示为Android的复合亚行界面

当我在shell中运行ADB设备，该设备显示了一会儿，然后消失。 在Eclipse控制台，我得到以下信息： [2010-11-13 11点54分42秒 - 设备监视器]未能开始监视

我已经重新启动了电脑几次，卸载和重新安装驱动程序几次，但我一次比一次同样的错误。当我在研究这个问题，有人建议重新启动手机。我有点由困惑 - 是软还是硬重启？难道我刚通电的手机关机/对，是有一些更复杂的参与？我一定要硬重启它重置为出厂版本 - 即使它的全新

有没有人遇到过类似的问题？任何帮助将是巨大的。 我无法测试我的设备上的应用程序，如果亚行不能查看设备。在此先感谢这么多。

解决方案

我有同样的问题。得到它的工作，做到以下几点：

关闭Eclipse 开启任务管理器，并杀死了 adb.exe 程序。 重新打开Eclipse（Eclipse将自动重启adb.exe服务）

运行 ADB设备在命令提示符下，你应该看到类似以下内容：

  C：\＆GT; ADB设备
设备名单附后
0123456789ABCDEF设备
 

当然，我假设你有你的手机插入到您的计算机。

I am running Android SDK 2.2 and am trying to get the adb to connect to the Google Nexus One phone. Its a new phone, shipped straight from Google - haven't installed any apps on it yet. (I have Windows XP) Here is what I have done so far:

Followed the instructions on setting up the device for development as given on the Android Developer's site: http://developer.android.com/guide/developing/device.html

added android:debuggable="true" to my application manifest

USB debuggable is checked on the phone

downloaded the Device Drivers For Windows Revision 3 (this supports Nexus One phones)

Went through the Hardware Installation wizard to install the device - the device shows up as "Android Composite ADB Interface".

When I run adb devices on the shell, the device appears for a moment, then disappears. On the Eclipse console, I get the following message: [2010-11-13 11:54:42 - DeviceMonitor]Failed to start monitoring

I have rebooted the pc several times, uninstalled and reinstalled the drivers several times, but I get the same error each time. As I was researching this problem, someone had recommended rebooting the phone. I am a bit confused by that - is that a soft or hard reboot? Do I just power the phone off/on and is there something more complex involved? Do I have to hard reboot it to reset to factory version - even though its brand new?

Has anyone run into a similar problem? Any help on this would be great. I can't test my application on the device if the adb cannot view the device. Thanks so much in advance.

解决方案

I had this same problem. To get it working, do the following:

Close Eclipse Open Task Manager and kill the adb.exe program. Re-open Eclipse (Eclipse will automatically restart the adb.exe service)

Run adb devices from a command prompt and you should see something like the following:

C:\> adb devices
List of devices attached
0123456789ABCDEF        device

Of course, I'm assuming you have your phone plugged into your computer.